Week 12

Transistors

The bipolar junction transistor is a current-controlled valve: a small base current allows up to β times as much collector current. Building on the diode models of week 11, you treat the base-emitter junction as a 0.7 V drop and decide whether the transistor is in cutoff, the active region or saturation. Most of the week is transistor switches driving motors and inductive loads, with flyback diodes; it also covers bias circuits and the gain of a common-emitter amplifier, which you built in last week's lab.

Objectives

  • State the conditions for cutoff, active and saturation regions of an NPN transistor (vBE, iB, vCE, and iC = βiB or iC < βiB), and the reversed versions for a PNP.
  • Find IB, IC, VC or VCE, and the transistor power PQ for NPN low-side, PNP high-side and emitter-follower switch circuits with the switch open and closed.
  • Decide whether a transistor is in the active region or saturated by assuming one, solving, and checking VCE against 0.2 V, then recalculating if the assumption fails.
  • Find the largest base resistor, smallest β, smallest drive voltage or smallest load resistance that keeps a transistor switch in saturation.
  • Explain why an inductive load needs a flyback diode, say when the diode conducts, and find its peak current.
  • Analyze two-transistor switch circuits, including an inverting stage that steers base current away from an output transistor.
  • Explain how an H-bridge drives a DC motor in both directions and which transistors must be on together.
  • Find VB, VE, IC and VC of a voltage-divider bias circuit with an emitter resistor, both neglecting IB and using the Thévenin base equivalent with βRE.
  • Estimate the voltage gain of a common-emitter amplifier as −RC/RE, and use re = 25 mV/IC to see why bypassing RE raises the gain.

Reading

4.3Transistors: bipolar transistors (how they work, formulas and rules, water analogy, switch, current source, emitter follower, common-emitter amplifier, Darlington pair, relay driver), then JFETs, MOSFETs, IGBTs and UJTs. Focus on 4.3.1 and 4.3.2 through the common-emitter amplifier, which match the notes; the FET sections introduce the other transistor families.

Lectures

1
Part 1Open original recording
58:16
2Examples 2–425:06
3
Part 2Open original recording
38:03
4
Part 3Open original recording
18:51
2:20:16

Notes

From the notes pack:

  1. Transistor Notes (BJT): hydraulic valve analogy, NPN symbol and terminals, β, the transistor only allows current that an outside source drives
  2. Switch versus amplifier use; cutoff, active and saturation regions; PNP transistors and FETs mentioned
  3. BJT structure as two pn junctions (checking a transistor with an ohmmeter diode setting), NPN and PNP symbols and subscripts, and a table of regions of operation (vBE about 0.7 V, vCE above 0.2 V in active, about 0.2 V in saturation)
  4. The transistor as a switch: motor driver from a logic output, base resistor, VCC terminal notation, flyback diode across an inductive load
  5. H-bridge: four transistors to reverse a motor, the shoot-through mistake, a two-input version with inverting transistors and pull-up resistors, and flyback diodes
  6. Linear amplifiers: active-region relations, bias, DC (capital) versus AC (lower case) notation, clipping from cutoff or saturation, emitter resistor for stable bias
  7. DC analysis in the active region: neglecting IB (divider gives VB) when RB1 ∥ RB2 is much less than βRE, otherwise the Thévenin base equivalent with RE looking β times bigger
  8. DC bias examples: 1) VB = 3 V, VCC = 20 V, RC = 10 kΩ, RE = 2.7 kΩ; 2) divider bias with VCC = 10 V, RB1 = 8 kΩ, RB2 = 2 kΩ, RE = 220 Ω; 3) designing RE, RC, RB1, RB2 with β = 150
  9. AC analysis of the common-emitter amplifier: base-to-collector gain RC/RE, small-signal emitter resistance re = 25 mV/IC, effect of a bypass capacitor; input impedance, output impedance and gain with source and load resistances; example gain RC/RE = 1 kΩ/120 Ω
  10. Transistor switching circuit examples: Ex. 1 NPN switch with VCC = 12 V, RC = 100 Ω, RB = 5 kΩ at β = 100 and 200 (saturation depends on β, RC and VCC; largest RB for saturation)
  11. Ex. 2 emitter follower driving RE = 50 Ω; Ex. 3 PNP high-side switch for a grounded load; Ex. 4 two-transistor inverting switch
  12. Ex. 5 to Ex. 8, from past finals: transistors driving inductive loads with flyback diodes, finding minimum VS, minimum RL, maximum R1, minimum β, transistor power, and the peak diode current when the switch opens

Homework

TR1: Transistor switches

  1. 1a–b. NPN low-side switch: VCC = 12 V, motor (modeled as 20 Ω, with a flyback diode) in the collector, base driven from VBB = 5 V through a switch and RB = 150 Ω, β = 25: find IC, VB, VC, PQ and IB with the switch open (a) and closed (b)
  2. 1c–d. NPN emitter follower: collector at 12 V, motor (20 Ω, with flyback diode) from emitter to ground, base switched directly to 5 V: find VB, VE, IB, IE and PQ with the switch open (c) and closed (d)
  3. 1e–f. PNP high-side switch: emitter at VCC = 15 V, motor (20 Ω, with flyback diode) from collector to ground, base pulled to ground through RB = 420 Ω and a switch: find VB, IB, VC, IC and PQ with the switch open (e) and closed (f)
  4. 1g–h. Two-transistor switch: Q1's base is driven from 5 V through RB = 2.2 kΩ and a switch; R2 = 360 Ω from 12 V feeds Q1's collector and Q2's base; Q2 switches the motor (20 Ω, with flyback diode) from 12 V: find IR2, IC2, VC2, VC1 = VB2, VB1, IB2 and IB1 with the switch open (g) and closed (h)
  5. 2. In 1b, find the largest RB that still keeps the transistor saturated
  6. 3. In 1f, find the largest RB that still keeps the transistor saturated
  7. 4a. V1 = 3 V drives the base through R1 = 500 Ω; the collector goes to V2 = 8 V through R2 = 30 Ω; with β = 40 and the active region assumed, find IC, VCE and PQ
  8. 4b. Check whether the transistor really is in the active region, using a value and its allowed range
  9. 4c. With β = 40, find the largest R1 that saturates the transistor
  10. 4d. With R1 = 500 Ω fixed, find the smallest β that saturates it
  11. 5a. VCC = 4 V, inductive load LL = 50 mH, RL = 5 Ω with a flyback diode in the collector; base driven from VS = 3 V through RS = 200 Ω, a switch and R1: find the load current with the transistor saturated
  12. 5b. With β = 80, find the largest R1 that keeps it saturated
  13. 5c. With that R1 and a bad transistor (β = 40), find IC, VCE and PQ
  14. 5d. Choose when the flyback diode carries significant current (never, when the switch opens, while open, when it closes, while closed, always)
  15. 5e. Find the maximum diode current after switching a few times
  16. 6a. VCC = 5 V, inductive load LL = 150 mH and RL = 10 Ω with a flyback diode, base driven by a 0 to 10 V pulse train; with VCE = 0.2 V when on, find the maximum load current
  17. 6b. Find the maximum diode current
  18. 6c. Sketch the diode current waveform under the given vin pulses