Week 5

Capacitors and inductors

Voltages and currents can now change with time, so the course adds the two energy-storing parts: the capacitor (i = C dv/dt) and the inductor (v = L di/dt). You learn their integral and derivative relations, series and parallel combinations, stored energy, DC steady state (capacitor open, inductor short), and why capacitor voltage and inductor current cannot jump. The week ends with the 90° phase shifts of sinusoids in C and L and LC resonance, which set up transients (week 6) and phasors (week 7).

Objectives

  • Sketch a capacitor's current from a piecewise voltage graph, or its voltage from a current graph, using i = C dv/dt and Δv = (1/C)∫i dt, with labeled values at each breakpoint.
  • Sketch an inductor's voltage from a piecewise current graph, or its current from a voltage graph, using v = L di/dt and Δi = (1/L)∫v dt.
  • Combine capacitors and inductors in series and parallel into Ceq and Leq (capacitors combine like conductances, inductors like resistors).
  • Find capacitor voltages and inductor currents in a DC circuit that has been connected a long time by replacing capacitors with opens and inductors with wires, then compute the stored energy ½CV² and ½LI².
  • Apply the rules that capacitor voltage and inductor current cannot change instantly, while capacitor current and inductor voltage can, to find values just after a switch moves.
  • Differentiate or integrate a sinusoidal voltage or current to find the other quantity for a capacitor or inductor, giving amplitude I/(ωC) or ωLI and the 90° lag (capacitor voltage) or lead (inductor voltage).
  • Find the resonant frequency f0 = 1/(2π√(Leq Ceq)) of an LC circuit and explain why a series LC looks like a short and a parallel LC like an open at f0.
  • Decide from a component's voltage and current graphs whether it is a capacitor or an inductor, and compute its value from the area under the current or voltage curve.
  • Read capacitor markings such as 104, 473J and 0.33 µF ±5%, and connect a polarized electrolytic capacitor the right way round.
  • Measure an RC charging and discharging time constant (63% and 37% points), accounting for the loading of an analog meter, and compare with τ = RC.

Reading

2.23The capacitor section: capacitance, energy stored, the RC time constant, series and parallel capacitors, AC current in a capacitor, capacitive reactance and the capacitive divider. Focus on 2.23.7 to 2.23.13.
3.6Practical capacitors: real-capacitor non-idealities, specifications, the main types (ceramic, film, electrolytic), and how to read markings. Use it as reference for the lab parts and the marking codes in the notes.
2.24The inductor section: self-inductance, the inductor equations, stored energy, energizing and de-energizing an RL circuit, switching spikes, and series and parallel inductors. Focus on 2.24.6, 2.24.7, 2.24.10, 2.24.11 and 2.24.16.

Lectures

1
CapacitorsOpen original recording
46:28
2
InductorsOpen original recording
44:38
1:31:06

Notes

From the notes pack:

  1. Capacitor basics: fluid (piston and spring) model, C = εA/d = Q/V, farad units
  2. Capacitor equations: i = C dv/dt, integral forms with initial voltage, energy ½CV², voltage cannot change instantly
  3. Capacitor construction and markings (0.33 µF ±5%, 473J = 47000 pF, 221, 472)
  4. Electrolytic capacitors: construction and polarity
  5. Capacitors in parallel and series
  6. Charging an RC circuit: voltage and current curves, τ = RC
  7. Initial condition vC(0−) = vC(0+) and final condition with the capacitor as an open
  8. Sinusoids in a capacitor: Vp = Ip/(ωC), voltage lags current by 90°
  9. Capacitor examples: Ceq combinations, energy stored in a DC circuit, drawing current from a voltage graph
  10. Inductor basics: flywheel fluid model, L = µN²K, henry units
  11. Inductor equations: v = L di/dt, integral forms with initial current, energy ½LI², current cannot change instantly
  12. Inductors in series and parallel
  13. Energizing an RL circuit: current and voltage curves, τ = L/R
  14. Initial condition iL(0−) = iL(0+) and final condition with the inductor as a short
  15. Sinusoids in an inductor: Vp = ωL Ip, voltage leads current by 90°
  16. Resonance: ω0 = 1/√(LC), series LC looks like a short and parallel LC like an open, reactance curves
  17. Examples: energy in L and C at DC steady state, resonant frequency of combined L's and C's, inductor voltage from a current graph, inductor current from a voltage graph, identifying an unknown component
  18. Summary sheet: capacitor and inductor equations, impedances, the first-order transient formula, and RC and RL charge and discharge curves

Homework

Cap1: Equivalent capacitance and stored energy

  1. 1a) Find Ceq of 0.2 µF in parallel with 0.4 µF
  2. 1b) Find Ceq of 0.02 µF in series with 0.06 µF
  3. 1c) Find Ceq of C1 = 3 µF in parallel with the series combination of C2 = 3 µF and (C3 = 1.2 µF in parallel with C4 = 1.8 µF)
  4. 2a) DC steady state: a 5.5 V source drives R1 = 220 Ω in series with R2 = 330 Ω, and a 5 µF capacitor sits across R2; find the capacitor voltage and stored energy
  5. 2b) DC steady state: a 25 mA current source with R2 = 1.5 kΩ across it, and R1 = 2.4 kΩ in series with a 0.47 µF capacitor also across the source; find the capacitor voltage and stored energy
  6. 2c) DC steady state: a 16 V source feeds R1 = 22 kΩ (with C2 = 0.22 µF across R1) into a node that has R3 = 10 kΩ to ground and R2 = 4.8 kΩ in series with C1 = 0.68 µF to ground; find the voltage and energy of each capacitor

Cap2: Capacitor waveforms and sinusoids

  1. 1) A square-wave current flows through a 0.025 µF capacitor: +0.15 mA from 0 to 0.3 ms, −0.1 mA from 0.3 to 0.6 ms, +0.15 mA from 0.6 to 0.9 ms, then −0.1 mA; with v(0) = 0, draw and label the capacitor voltage
  2. 2) The voltage on a 2 µF capacitor ramps from 0 to −6 V over 0 to 2 ms, stays at −6 V to 3 ms, ramps to +6 V at 5 ms, stays at 6 V to 6 ms, then falls along a parabola (zero slope at 6 ms) to 0 V at 9 ms; draw and label the current
  3. 3) vC(t) = 6 V cos(200t + π/2) on a 0.68 µF capacitor; find iC(t)
  4. 4) iC(t) = 18 µA cos(628t − π/4) through a 0.0047 µF capacitor; find vC(t)
  5. 5) A capacitor's voltage ramps from about −4 V at 0.5 ms to +8 V at 2 ms while its current is a constant 2 mA over the same interval; find the capacitance

Ind: Inductors, stored energy and resonance

  1. 1a) Find Leq of 2 mH in parallel with 3 mH
  2. 1b) Find Leq of 0.22 mH in series with 0.4 mH
  3. 2a) DC steady state: a 10 V source drives R = 200 Ω in series with L = 40 mH; find the inductor's stored energy
  4. 2b) DC steady state: an 18 V source has C1 = 10 µF across it and feeds L1 = 0.5 mH into node A; from A, L2 = 4 mH in series with R2 = 60 Ω goes to ground, and R1 = 30 Ω (with C2 = 2 µF across it) goes to R3 = 30 Ω to ground; find the energy in C1, L1, C2 and L2
  5. 3) The current in a 2 mH inductor ramps from 0 to −8 mA over 0 to 2 ms, stays at −8 mA to 3 ms, ramps to +8 mA at 5 ms, stays at 8 mA to 6 ms, then falls along a second-order curve (zero slope at 6 ms) to 0 at 9 ms; draw and label the inductor voltage
  6. 4) The voltage on a 0.5 mH inductor is 3 V from 0 to 0.2 ms, −2 V from 0.2 to 0.6 ms, ramps from −2 V to +3 V between 0.6 and 1.0 ms, then 0; with i(0) = 0, draw and label the inductor current
  7. 5) vL = 4 mV cos(300t) across a 1.2 mH inductor; find iL
  8. 6) iL = 20 mA cos(628t − π/4) through a 0.08 mH inductor; find vL
  9. 7) For a sinusoidal source driving a capacitor and an inductor in parallel, find iC and iL by differentiation and integration and show they are equal and opposite at ω0 = 1/√(LC)
  10. 8a) Find f0 for 0.1 µF, 0.22 µF, 0.5 mH and 0.5 mH all in parallel
  11. 8b) Find f0 for two 0.12 µF capacitors in series, in parallel with a 10 mH and a 5 mH inductor in series

Lab: Capacitors (ECE 2210/2200 Lab 5)

Charge and discharge a 47 µF capacitor through 100 kΩ while watching an analog meter, and time the 63% and 37% points to measure the RC time constant. Then drive a 1 kΩ and 0.1 µF divider with sine waves to see how capacitor voltage falls with frequency, and use the scope's subtract function to show that KVL holds for instantaneous voltages even though peak-to-peak values don't add.

Before the lab

  • Read the capacitor background in the handout: marking codes (104 = 10 × 10⁴ pF = 0.1 µF, letter = tolerance: F 1%, G 2%, J 5%, K 10%, M 20%) and electrolytic polarity
  • Work out the meter loading: the BK analog meter on its 10 V DC range looks like 25 kΩ/V × 10 V = 250 kΩ, so 14 V through 100 kΩ looks like a 10 V source with a 71 kΩ Thévenin resistance
  • Calculate τ for charging (71 kΩ × 47 µF ≈ 3.4 s) and discharging through the meter alone (250 kΩ × 47 µF ≈ 11.8 s)
  • Calculate τ for two 47 µF capacitors in parallel (94 µF) and in series (23.5 µF)
  • For the RC filter, compute the theoretical capacitor voltage at each test frequency: |VC| = Vs / √(1 + (2πfRC)²) with R = 1 kΩ and C = 0.1 µF (the handout's appendix with these values is not in the materials)

Equipment

  • Bench DC power supply
  • Analog multimeter (BK Precision or similar, from the stockroom)
  • Stopwatch, watch or clock
  • Function generator (Agilent/HP 33120A, 50 Ω internal resistance)
  • Oscilloscope (two channels, with math subtract and cursors)
  • Two scope probes
  • Breadboard and jumper wires

Parts

11 kΩ resistorbrown black red
1100 kΩ resistorbrown black yellow
10.1 µF capacitormarked 104
247 µF electrolytic capacitorpolarized: the band marks the negative lead

Procedure

  1. Inspect the capacitors
    • Compare the 47 µF and 0.1 µF capacitors: the 47 µF is bigger, but not 470 times bigger
    • Find the voltage rating on the electrolytic and the whitish band that marks the negative lead (go by the band, not lead length)
    • Never exceed the voltage rating or reverse the polarity of the electrolytic: it can blow up
  2. Charge and discharge
    • Set the bench supply to about 14 V
    • Wire the supply's red terminal to a free point A, then A (left unconnected for now) to 100 kΩ, to the + lead of a 47 µF capacitor; connect the capacitor's − lead to the supply's black terminal
    • Connect the analog meter, on its 10 V DC range, across the capacitor
    • If the meter does not read 0 V, short the capacitor leads together for a second
    • Connect point A to the supply and watch the voltage rise; let it charge until it barely changes, near 10 V (the meter's 250 kΩ loading keeps it from reaching 14 V)
    • Disconnect point A from the supply and watch the capacitor discharge through the meter alone (slower, since the 100 kΩ is out of the circuit)
  3. Measure the time constant
    • Repeat the charge with a stopwatch and time how long the voltage takes to reach 63% of 10 V (6.3 V)
    • Repeat the discharge and time how long it takes to fall to 37% of the fully charged voltage
    • Quickly repeat both timings with the two 47 µF capacitors in parallel, then with the two in series
  4. RC filter frequency response
    • Build the divider: function generator output to 1 kΩ, to 0.1 µF, to ground (the generator's 50 Ω internal resistance is in series)
    • Scope CH1 at the generator output (top of the 1 kΩ), CH2 at the resistor-capacitor junction (across the capacitor), probe grounds to circuit ground
    • Set both scope channels to match the probes (1x or 10x)
    • Set the generator to an 8 Vpp sine at about 100 Hz (the generator display may need 4 Vpp, since it assumes a 50 Ω load)
    • Measure the capacitor's peak-to-peak voltage (CH2) at 100 Hz, 300 Hz, 1 kHz, 3 kHz, 10 kHz, 30 kHz and 100 kHz
    • At 3 kHz also note the resistor and capacitor peak-to-peak voltages
  5. Phase and instantaneous KVL
    • Set the generator back to 3 kHz; turn on both channels at 1 V/div
    • Use each channel's vertical position knob to put its ground marker on the screen's center line
    • See whether VS (CH1) and VC (CH2) peak at the same instant
    • Press Math, Operator, Subtract to show CH1 − CH2, which is the resistor voltage VR
    • Use the cursors to read the instantaneous levels of VS, VC and VR at one time, then at two more times

Record

  • Rough sketch of the charging curve and a comment on whether it follows the RC charging shape
  • Sketch of the discharge curve and comment; answer: the meter's current came from no supply, so where did the energy come from?
  • Measured charge and discharge time constants compared with 3.4 s and 11.8 s
  • Time constants with two 47 µF capacitors in parallel and in series, with a comment on series and parallel capacitors
  • Table of capacitor Vpp at the seven frequencies, plotted on seven evenly spaced divisions (an approximate log axis) or on log paper, with the theoretical values plotted on the same axes and compared
  • Answer: at 3 kHz the resistor and capacitor peak-to-peak voltages add to more than the source's; is that a violation of KVL?
  • Answer: do VS and VC peak at the same instant?
  • Three sets of instantaneous VS, VC and VR readings, and whether VC + VR = VS at each instant
  • Conclusion touching each objective (charge and discharge, time constant, frequency dependence, phase and KVL); get the check-off