Week 1

Kirchhoff's laws, resistance, Ohm's law, power

The course starts with charge, current, and voltage, using a fluid analogy: current is like flow and voltage is like pressure. Kirchhoff's current and voltage laws, Ohm's law, and power follow. Resistors are then combined in series and parallel, and voltage and current dividers split voltage and current between them. Everything later in the course rests on these tools.

Objectives

  • Apply Kirchhoff's current law at nodes and around closed sections to find unknown branch currents, and interpret a negative result as flow opposite the arrow
  • Apply Kirchhoff's voltage law around loops to find unknown element voltages from marked + and − polarities, including circuits with two sources
  • Use Ohm's law (V = IR) and the power relations P = VI = I²R = V²/R to find any missing voltage, current, resistance, or power
  • Reduce a resistor network to its equivalent resistance between two terminals by repeatedly combining series and parallel resistors
  • Find the voltage across a resistor in a series string with the voltage divider rule, combining resistors first when needed
  • Find the current through one of several parallel resistors with the current divider rule
  • Decide from voltage polarity and current direction whether each element absorbs or supplies power, and show that power supplied equals power absorbed
  • Analyze a Wheatstone bridge as two voltage dividers and find its output voltage when the resistances change
  • Read a resistor's nominal value and tolerance from its 4-band or 5-band color code

Reading

1An overview of what electronics covers and the order to learn it: theory, passive components and circuits, semiconductors, integrated circuits, and input and output devices. Skim it for the map.
2.1–3Electric current as moving charge, and voltage: how it arises, the definition of the volt, the generalized power law P = VI, combining batteries, and water analogies. Focus on current direction and P = VI.
2.17Kirchhoff's voltage law (loop rule) and current law (junction rule), with sign rules for tracing a loop and a worked six-unknown example. Focus on the sign conventions, not on the determinant method.
2.5–7Resistance and resistivity (how a conductor's shape sets its resistance), insulators, conductors, and semiconductors, and heat and power in resistors.
2.11–12What a circuit is, then Ohm's law and resistors: power ratings, resistors in parallel and series, reducing a complex network, and voltage dividers. This is the core reading for the week.
3.5Practical resistors: reading color codes and labels, real characteristics, types, and potentiometers. Use it with the color code chart in the notes.

Lectures

1
Course introOpen original recording
29:58
2
Kirchhoff's lawsOpen original recording
40:46
3
ResistorsOpen original recording
55:15
2:05:59

Notes

From the notes pack:

  1. Course intro: ECE 2200 vs 2210, homework turned in as PDF on Canvas, labs need a notebook and a U-card
  2. How to survive the class and why engineers need circuits: information processing, power and energy, preparation for later subjects
  3. Basic quantities with the fluid analogy: charge (C), current (A) like flow, voltage (V) like pressure
  4. KCL: current in equals current out of any point, part, or section; a negative current means the arrow is backwards
  5. Conductors vs nonconductors, the no-charge-buildup simplification, and why current must circulate in a circuit
  6. KVL: voltage gains equal voltage drops around any loop, with the pump and turbine analogy
  7. Ideal elements: voltage sources, ideal wires, ideal resistors, and connected vs unconnected wire crossings
  8. In-class circuits for spotting series and parallel resistors
  9. Ohm's law, the definition of the ohm, power P = VI = V²/R = I²R, and units of resistance, conductance, and power
  10. Series resistors (same current) and parallel resistors (same voltage) and their equivalent resistance
  11. Reducing a 14-resistor network, and a bridge network that series and parallel rules cannot reduce
  12. Voltage divider and current divider formulas, and combining resistors before applying them
  13. Resistor I–V lines (R = 1/slope), ideal voltage and current sources and their I–V lines, and connections that make no sense (shorted voltage source, open current source)
  14. Ground symbols and ground as the 0 V reference
  15. Nodes (all points joined by wire) and branches (parts carrying the same current)
  16. Meters: ideal voltmeter is an open, ideal ammeter is a short; analog meter internals and the digital meter block diagram
  17. Additional series-parallel examples, including networks driven by a current source
  18. Resistor color code chart (4-band and 5-band) with standard E24 and E96 values

Homework

DC1: Kirchhoff's current and voltage laws with fluid analogies

  1. Hydraulic loop with one pump feeding two unequal turbines in parallel; given flows I1 = 0.01 m³/s and I2 = 0.007 m³/s, find I3 to I6 by KCL
  2. Electrical version: a battery feeding two unequal resistors in parallel; given I1 = 0.01 A and I2 = 0.007 A, find I3 to I6
  3. Same battery and two-resistor circuit with current arrows drawn beside the wires; given I2 = 20 mA and I5 = 14 mA, find I6, I1, I3, I4
  4. Hydraulic loop with a series turbine, two turbines in parallel, and a series return turbine; given I3 = 0.004 m³/s and I5 = 0.001 m³/s, find I1, I2, I4, I6, I7, I8
  5. Electrical analog: battery, series resistor, two parallel resistors, series return resistor; given I3 = 4.5 mA and I5 = 1.2 mA, find the other six currents
  6. Same circuit with arrows beside the wires; given I6 = 0.03 A and I7 = 0.08 A, find I1 to I5 and I8
  7. Two pumps with dead-end (closed) pipes on each side; given I9 = 0.04 m³/s, find I1 to I8 and I10
  8. Electrical analog with two batteries and dangling, unconnected wires; given I9 = 0.06 A, find all ten currents
  9. One pump driving a five-turbine network; given I4 = 0.05, I5 = 0.014, I6 = 0.03 m³/s, find I1, I2, I3, I7
  10. Battery driving a four-resistor network; given I4 = 20 mA, I5 = 10 mA, I6 = 22 mA, find I1, I2, I3, I7
  11. Two-pump hydraulic network; given I2 = 0.005, I6 = 0.03, I7 = 0.015 m³/s, find I1, I3, I4, I5 (at least one comes out negative)
  12. Explain what a negative fluid flow means physically
  13. Two-battery resistor network; given I1 = 0.01 A, I5 = −20 mA, I6 = 35 mA, find I2, I3, I4, I7
  14. Explain what a negative electrical current means physically
  15. Larger one-pump hydraulic network; given I4 = 0.05, I5 = 0.03, I7 = 0.045, I9 = 0.06 m³/s, find I1, I2, I3, I6, I8, I10, I11
  16. Larger battery-and-resistor network; given I1 = 100 mA, I2 = 50 mA, I3 = 30 mA, I6 = 66 mA, find I4, I5, I7 to I11
  17. KVL with pressures: a pump supplying ΔPS = 12 Pa to two turbines in parallel; find ΔP2 and ΔP4
  18. Battery VS = 12 V across two resistors in parallel; find V2 and V4
  19. Hydraulic loops: pump ΔPS = 400 kPa, series turbine ΔP1 = 180 kPa, parallel turbine ΔP3 = 100 kPa; find ΔP5 and ΔP7
  20. Battery with series resistor V1 = 10 V, two parallel resistors (V3, V5 = 3 V), and return resistor V7 = 2 V; find VS and V3
  21. Two pumps with dead-end pipes: ΔPS1 = 200 kPa, ΔPS2 = 150 kPa, ΔP2 = 50 kPa, ΔP6 = 60 kPa; find ΔP4 and ΔP7
  22. Two batteries: VS1 = 6 V, V2 = 2 V, V6 = 2.4 V, V7 = 3.2 V; find VS2 and V4
  23. Pump and five-turbine network: ΔP3 = 120 kPa, ΔP4 = 80 kPa, ΔP6 = 110 kPa; find ΔPS, ΔP2, ΔP5
  24. Explain what a negative pressure difference means physically
  25. Battery and five-resistor network: V3 = 2.3 V, V5 = 0.5 V, V6 = 3.2 V; find VS, V2, V4
  26. Two-pump network, watching + and − signs: ΔP2 = 140, ΔP3 = 230, ΔP4 = 50, ΔP6 = 210 kPa; find ΔPS1, ΔPS2, ΔP5
  27. Two-battery circuit: VS1 = 14 V, VS2 = 3 V, V2 = 6 V, V3 = 4 V; find V4, V5, V6, and say what is happening to the second battery
  28. Larger hydraulic network: ΔP1 = 200, ΔP2 = 1100, ΔP3 = 600, ΔP9 = 1800 kPa; find ΔPS, ΔP4, ΔP5, ΔP6, ΔP10
  29. Battery VS = 18 V in series with a resistor (V1) driving a seven-resistor network: V3 = 6 V, V4 = 8 V, V5 = 2 V; find V1, V2, V6, V9, V10

DC2: Ohm's law, power, and equivalent resistance

  1. Ohm's law for a source driving one resistor: (a) I = 0.01 A, VR = 4 V, find R; (b) I = 50 mA, R = 560 Ω, find VR; (c) VR = 12 V, R = 1.5 kΩ, find I
  2. Ohm's law and power, same circuit: (a) I = 5 mA, R = 2 kΩ, find VR and PR; (b) VR = 25 V, R = 100 Ω, find I and PR; (c) VR = 20 V, I = 0.01 A, find R and PR
  3. Appliances treated as resistors: (d) 900 W toaster on 120 V, find I and R; (e) 1500 W hair drier with R = 9.6 Ω, find I and VS; (f) 2500 W oven drawing 10.5 A, find R and VS
  4. (3a) Equivalent resistance of four resistors in series: 1.8 kΩ, 1.0 kΩ, 2.5 kΩ, 5.6 kΩ
  5. (3b) Equivalent resistance of four resistors in parallel: 1.5 kΩ, 2.2 kΩ, 900 Ω, 3 kΩ
  6. (3c) 120 Ω in series with two 80 Ω resistors in parallel
  7. (3d) 110 kΩ in series with (68 kΩ in parallel with 82 kΩ), and that whole string in parallel with 180 kΩ
  8. (3e) 150 Ω in parallel with the series pair 56 Ω and 22 Ω
  9. Start homework DC3 now

DC3: Equivalent resistance, dividers, and power

  1. (1a) Equivalent resistance of R1 = 60 kΩ in parallel with R3 = 80 kΩ, in series with R2 = 100 kΩ in parallel with R4 = 120 kΩ; keep intermediate results for later problems
  2. (1b) Equivalent resistance between the terminals of a seven-resistor network: R1 = 22 Ω, R2 = 100 Ω, R3 = 20 Ω, R4 = 30 Ω, R5 = 75 Ω, R6 = 40 Ω, R7 = 25 Ω
  3. (2a) Series loop of VS = 12 V with R1 = 1.5 kΩ, R2 = 1.0 kΩ, R3 = 2 kΩ: find each resistor voltage by the voltage divider rule
  4. (2b, 2c) Confirm the three voltages sum to VS (KVL), and say what happens to them if VS doubles or triples
  5. (3a) Wheatstone bridge of four 100 Ω strain gauges on a 10 V source, Vab taken between the two divider midpoints: find Vab
  6. (3b) R1 and R4 decrease 1% while R2 and R3 increase 1%: find Vab
  7. (3c, 3d) All four gauges increase 5% with temperature: find the % change in Vab, and explain why the bridge is used
  8. (4a) VS = 36 V drives the network of 1a in series with R5 = 30 kΩ: find VR5, VR4, VR1 by voltage dividers
  9. (4b) VS = 24 V drives R8 = 12 Ω in series with the network of 1b: find VR8, VR2, VR1
  10. (5a) Current source IS = 50 mA feeds R4 = 1.5 kΩ to ground in parallel with R1 = 1 kΩ leading to R2 = 0.68 kΩ in parallel with R3 = 0.82 kΩ to ground: find IR1 to IR4 by current dividers
  11. (5b, 5c) Confirm KCL twice (IR2 + IR3 = IR1, IR1 + IR4 = IS), and say what happens if IS doubles or triples
  12. (6) For the circuit of 4b: find the resistance the source sees and the source current, then IR2, IR1, IR4 by current dividers, and confirm the 4b voltages with Ohm's law
  13. (7) For the circuit of problem 2: find the power in each resistor and the source power, and show power is conserved
  14. (8) For the circuit of problem 5: find the power in each resistor and the source power, and show power is conserved
  15. (9) Five unknown components A to E in a two-loop circuit with ID = 0.2 A, IC = 0.3 A, VB = 2 V, VD = 8 V, VE = 4 V: find all voltages and currents, say which components absorb and which supply power, and show power balances