Week 2
Dividers, sources, superposition
This week finishes the vocabulary of circuits: nodes, branches, ground, ideal voltage and current sources, and how meters connect. It then introduces superposition, which solves circuits with more than one source by taking one source at a time and adding the results. The first lab teaches the bench instruments, breadboard wiring, and the lab notebook, and checks Ohm's law and series and parallel resistance with real measurements.
Objectives
- Identify the nodes and branches of a schematic, treating all ground symbols as one 0 V reference node
- Describe ideal voltage and current sources by their I–V lines, and recognize impossible connections such as a shorted voltage source or an open current source
- Connect a voltmeter across an element and an ammeter in series by breaking the circuit open, knowing an ideal voltmeter acts as an open and an ideal ammeter as a short
- Use superposition to find a voltage or current in a circuit with several independent sources: zero all but one (voltage source to short, current source to open), solve, repeat, and add with signs
- Explain how a cell works, the difference between primary and secondary batteries, battery capacity in Ah, and why terminal voltage drops under load
- Build a resistor circuit on a breadboard, take current and voltage readings with a DC supply and DMM, plot I vs V, and find resistance as 1/slope
- Keep a dated lab notebook with circuit drawings, labeled data tables, graphs drawn to scale, and a conclusion that addresses each objective
Reading
| 2.10 | Grounds: earth ground, the different ground symbols, and ground as the common reference for voltages in a circuit. |
| 2.12–16 | Ohm's law and resistors (including voltage dividers), voltage and current sources, measuring voltage, current, and resistance with meters, combining batteries, and open and short circuits. Focus on 2.13 (sources) and 2.14 (meters). |
| 2.18 | The superposition theorem for linear circuits with more than one source, with a worked example. Focus on how each source is zeroed. |
| 3.2 | Batteries: how a cell works, primary and secondary types, battery capacity, and the internal voltage drop of a real battery. Focus on 3.2.5 and 3.2.6, which lead into the practical source model. |
Lectures
| 1 | Dividers, sources, metersOpen original recording | 27:10 |
| 2 | SuperpositionOpen original recording | 28:38 |
| 55:48 |
Notes
From the notes pack:
- Superposition: the statics analogy, where reactions to several loads on a beam add
- Superposition steps: zero all but one source (voltage source becomes a short, current source becomes an open), compute the wanted quantity, repeat for each source, then sum with signs
- Ex 1: VS = 6 V and IS = 18 mA with R1 = 100 Ω and R2 = 200 Ω; find I2 and VR1 from each source and add
- Ex 2: VS = 12 V and IS = 2 mA with R1 = 1 kΩ, R2 = 2 kΩ, R3 = 3 kΩ; find VR2 and IR3, noting R1 drops out once a source is zeroed
- Pages 3 to 12 of this pack are the Thévenin and Norton notes, used in week 3
Homework
DC4: Superposition
- VS1 = 8 V feeds node a through R1 = 1 kΩ, VS2 = 10 V feeds node a through R2 = 500 Ω, and R3 = 1 kΩ runs from a to ground; use superposition to find I3, showing how much comes from each source
- (2a) VS1 = 5 V feeds node a through R1 = 40 Ω; R2 = 120 Ω in series with VS2 = 6 V and R3 = 120 Ω each run from a to ground; find Va and IR1 by superposition
- (2b) Three branches in parallel: R1 = 11 Ω, R2 = 22 Ω in series with VS = 12 V, and IS = 0.5 A; find VR1 and IR2 by superposition
- (2c) R1 = 3 kΩ, R2 = 3 kΩ, and a 3 mA current source (pulling current to ground) share one node, which connects through R3 = 1 kΩ to node a; R4 = 2 kΩ in series with VS = 4.5 V runs from a to ground; find Va and IR1, watching signs
Lab: Introduction to the lab
Learn the bench power supply, digital multimeters, and breadboard, and how to keep the lab notebook. Measure I vs V for single, series, and parallel resistors to show resistors are linear and that V/I matches the equivalent resistance. Finish by powering the servo board that later labs build on.
Before the lab
- Read the lab notebook guidelines (reference/Notebook.pdf)
- Buy or check out the parts and bring a bound or spiral lab notebook
Equipment
- Agilent/HP E3631A triple-output DC power supply
- Agilent/HP 34401A bench digital multimeter
- Portable digital multimeter (checked out; used as the second meter in Experiment 2)
- Servo demonstration board (checked out from the stockroom)
- Lab notebook
Parts
| 1 | 100 Ω resistor | brown, black, brown, gold |
| 1 | 270 Ω resistor | red, violet, brown, gold |
| 1 | 560 Ω resistor | green, blue, brown, gold |
| 2 | 1 kΩ resistor | brown, black, red, gold |
| 2 | 2 kΩ resistor | red, black, red, gold |
| 1 | 2.2 kΩ resistor | red, red, red, gold |
| 1 | Breadboard with wires |
Procedure
- Set up the supply (TA demonstration)
- Start the notebook entry with title, date, and objectives
- Connect a 1 kΩ resistor across the +25V and COM outputs of the E3631A
- Turn the supply on, wait for OUTPUT OFF, press Output On/Off, then the +25V key, and turn the knob up to a few volts
- Note that the supply's built-in ammeter is not sensitive enough to read this current
- Check KVL with a voltmeter
- Put the DMM (as a voltmeter) across the 1 kΩ resistor
- Set several supply voltages and compare the DMM reading with the supply's display; after this you may trust the supply's voltmeter
- Experiment 1: I vs V for resistors
- Turn the supply output off before rewiring (an ammeter is nearly a short)
- Break the circuit and insert the DMM in series as an ammeter; press Shift then DC I on the meter, and turn the output back on
- Vary the supply from 0 V to 10 V and record current and voltage for the single 1 kΩ resistor
- Repeat with two 1 kΩ resistors in series (use the breadboard)
- Repeat with one 2 kΩ resistor, then with two 2 kΩ resistors in parallel
- Plot every case as a line on one I (mA) vs V graph, drawn to scale
- Experiment 2: voltage vs resistance at constant current
- Measure each of the six resistors (100 Ω, 270 Ω, 560 Ω, 1 kΩ, 2 kΩ, 2.2 kΩ) with the DMM on its Ω range, without touching the leads
- Wire all six in series with the ammeter and adjust the supply (knob and arrow keys) until the ammeter reads 4 mA
- Measure the voltage across each resistor with the second DMM
- Graph resistance on the x-axis vs volts needed for 4 mA on the y-axis
- Experiment 3: servo board
- On the E3631A press Output On/Off, then +25V, then hold Track for a few seconds so the − output tracks the + output; set + to 6 V for a ±6 V supply
- Press Store twice to save this as configuration 1 (Recall twice brings it back later)
- With the servo's switch off and the outputs off, connect the servo's red lead to + of the ±25V outputs, green/white to COM, and black to −; both + and − jacks are red, with − to the right of ground
- Turn on the outputs, then the servo; turn the input position shaft and watch the motor drive the output shaft to follow (turn down the gain if it oscillates)
- Estimate how many resistors are on the servo board and read the value of one from its color code
- Check-off and conclusion
- Call the TA to check you off before tearing down; be ready to demonstrate the circuit and discuss the notebook
- Write a conclusion that touches each objective and any problems you overcame
Record
- Circuit drawing for each circuit built, with instrument brand names on the first one
- Comment on the supply ammeter's sensitivity, and whether the resistor voltage equals the supply voltage
- Table of V and I for the 1 kΩ, two 1 kΩ in series, 2 kΩ, and two 2 kΩ in parallel, with space for all columns
- I vs V graph with one labeled line per circuit; comment on the shape and what it says about resistor linearity
- Slope of each line and V/I (1/slope) compared with the resistor or equivalent resistance values; comment on the effect of series and parallel
- Experiment 2 table: color code, nominal value, measured value, volts needed for 4 mA
- Graph of volts vs resistance at 4 mA, with a comment on how voltage relates to resistance at fixed current
- Short description of what the servo does, at least three uses for servos, and whether you expect to work with them
- Approximate number of resistors on the servo board and one resistor value read from its color code
- Conclusion covering every objective and any problems encountered