Week 3
Thévenin & Norton equivalents
A real source is modeled as an ideal source plus an internal resistance. The same model, the Thévenin equivalent, replaces any network of sources and resistors seen from two terminals, and the Norton equivalent is its current-source twin. With the equivalent in hand, the load voltage, current, and power for any load are one step away, and maximum power reaches the load when RL = RTh. Superposition from week 2 is the usual way to find VTh when there are several sources. The lab measures a Thévenin equivalent on the bench and on the servo's position sensor, and checks superposition with two supplies.
Objectives
- Model a battery or sensor as an ideal source with series internal (output) resistance from its open-circuit and loaded voltages, then predict its terminal voltage at another load current or while charging
- Find the Thévenin equivalent (VTh as the open-circuit voltage, RTh with all sources zeroed) of a resistive network with voltage and current sources, seen from the load terminals
- Find VTh of a network with several sources by superposition
- Find the Norton equivalent, either from the short-circuit current or by converting from Thévenin (RN = RTh, IN = VTh/RTh)
- Use a Thévenin or Norton equivalent to find the load voltage, current, and power for a given load resistor
- Choose the load resistance that maximizes load power (RL = RTh), compute that power, and explain why efficiency is only 50% there
- Measure VTh as an open-circuit voltage and RTh with an ohmmeter after zeroing the source, then build and verify the equivalent circuit with a trim potentiometer
- Verify superposition on the bench by zeroing one supply at a time and comparing the sum of the partial voltages with the full-circuit voltage
Reading
| 2.19 | Thévenin's and Norton's theorems: replacing a linear network with a single source and resistance, finding VTh and RTh, and converting to Norton form, with worked examples. |
Lectures
| 1 | Thévenin & NortonOpen original recording | 50:15 |
| 2 | Thévenin examplesOpen original recording | 35:33 |
| 1:25:48 |
Notes
From week 2's notes pack:
- Simple model of a real source: ideal VS in series with RS, and its terminal I–V line from VS/RS at short circuit to VS at open circuit
- The Thévenin equivalent circuit and the four steps: open-circuit voltage, zero the sources, resistance between the load terminals, draw the circuit
- Norton model: current source in parallel with RS, its I–V line, the Norton steps (short-circuit current), and the conversion RN = RTh, IN = VTh/RTh
- Ex 1: VS = 20 V, R1 = 40 Ω, R2 = 120 Ω with RL = 60 Ω; Thévenin and Norton equivalents and the load voltage, current, and power
- Equivalence check: VL and IL of the original and Thévenin circuits for RL from 0 Ω to open, the V–I line, and load power peaking at RL = RTh
- Maximum power transfer derived (RL = RS), and efficiency RL/(RS + RL), which grows as RL gets larger
- Ex 2: 18 V ladder with 1.5 kΩ, 3 kΩ, 2 kΩ, 1 kΩ and a 450 Ω load; Thévenin, Norton, load current, and maximum load power
- Ex 3: two voltage sources (10 V and 20 V) with 5 Ω and 15 Ω and a 20 Ω load between them
- Ex 4: 9 V source and 50 mA current source with 40 Ω, 120 Ω, 240 Ω and a 72 Ω load; VTh by superposition
- Ex 5: NiCd battery pack that drops from 4.80 V to 4.65 V at 50 mA; its model, the voltage at 300 mA, and the charging current from a 5.10 V charger
- Ex 6: 1 A source with 8 Ω parallel resistance; load for maximum power and that power
- Ex 7: 9 V source and 180 mA source with six resistors and a 30 Ω load; VTh by superposition, RTh, and the Norton equivalent
Homework
DC5: Thévenin and Norton equivalent circuits
- (1a) VS = 9 V feeds R1 = 6 kΩ to a node with R3 = 12 kΩ to ground, then R2 = 10 kΩ out to the load RL = 12 kΩ; find and draw the Thévenin equivalent
- (1b) Find VL and IL using the Thévenin equivalent
- (1c) Find and draw the Norton equivalent
- (2a) IS = 360 mA feeds R1 = 100 Ω to a node with R3 = 40 Ω to ground, then R2 = 60 Ω to a second node with R5 = 50 Ω to ground; the load RL = 120 Ω sits in series with R4 = 20 Ω from that second node to ground; find and draw the Thévenin equivalent seen by RL
- (2b) Find and draw the Norton equivalent of the same circuit
- (2c) Find the voltage across the load
- (2d) Choose RL for maximum load power and find that power
- (3a) Four branches in parallel: IS = 12 mA, R1 = 10 Ω, R2 = 50 Ω in series with VS = 6 V, and the load RL = 330 Ω in series with R3 = 10 Ω; find the Thévenin equivalent seen by RL (hint: superposition, or nodal analysis)
- (3b) Find and draw the Norton equivalent
- (3c) Find VL and IL using the Norton equivalent
DC6: Thévenin, Norton, and source resistance
- A 40 mA current source in series with R1 = 160 Ω drives R2 = 180 Ω in parallel with the series pair R3 = 100 Ω and R4 = 120 Ω; use Thévenin's theorem to find the current in R4
- A 1 A source in parallel with R1 = 20 Ω feeds R2 = 10 Ω to a node with R3 = 20 Ω to ground and R4 = 20 Ω leading to R5 = 10 Ω to ground; use Norton's theorem to find the current in R5 (the equal resistor values make the short-circuit current easy)
- (3a) A car battery's terminal voltage drops from 12.5 V to 8.5 V while the starter draws 80 A; draw its voltage-source (Thévenin) model with VS and RS
- (3b) Draw its current-source (Norton) model with IS and RS
- (3c) Decide which model is more appropriate for a car battery
- (3d) Find the terminal voltage while the battery is charged at 20 A
Lab: Thévenin equivalents and superposition
Measure the Thévenin equivalent of a 270 Ω and 560 Ω divider on a 10 V supply, build it from an adjustable supply and a trim pot, and show both circuits give the same I–V line. Then find the output resistance of the servo's Input Position potentiometer, and verify superposition with the two outputs of the bench supply.
Before the lab
- Calculate VTh and RTh of the 270 Ω and 560 Ω divider on 10 V (you may also do this after the lab)
- Review how to set the E3631A to ±6 V and connect the servo (Lab 1)
Equipment
- Agilent/HP E3631A triple-output DC power supply
- Agilent/HP 34401A bench digital multimeter
- Portable digital multimeter (checked out)
- Servo demonstration board (checked out)
- Small screwdriver for the trim pot
Parts
| 1 | 100 Ω resistor | load |
| 1 | 220 Ω resistor | new this lab; superposition circuit |
| 1 | 270 Ω resistor | |
| 2 | 390 Ω resistor | one as a load, one in the superposition circuit |
| 1 | 560 Ω resistor | |
| 1 | 1 kΩ resistor | superposition circuit |
| 1 | 500 Ω trim potentiometer | new this lab; sets RTh |
| 1 | Breadboard with wires | |
| 1 | 10 kΩ resistor | listed for this lab in the parts spreadsheet but not used in the handout; the servo board supplies its own 10 kΩ load |
Procedure
- Part 1: I vs V of the original circuit and VTh
- Set the supply to 10 V; connect 270 Ω from + to the output node and 560 Ω from the output node to −; the load terminals are across the 560 Ω
- Put an ammeter in series with the load and a voltmeter across the load
- Record I and V for RL = 0 Ω (short), 100 Ω, 390 Ω, and open circuit
- The open-circuit voltage is VTh (about 6.7 V)
- Parts 2 and 3: zero the source and measure RTh
- Zero the source by pulling the wire out of the supply's + jack and plugging it into the plug already in the − jack, so a short replaces the supply (never short the supply itself)
- Measure the resistance between the load terminals with an ohmmeter; this is RTh (about 180 Ω)
- Part 4: build and test the Thévenin circuit
- Put the 500 Ω trim pot in the breadboard, connect the ohmmeter between the wiper and one end, and adjust it to RTh; then build around it without touching it
- Set the supply to VTh and connect it in series with the pot to the load terminals, with the same ammeter and voltmeter
- Record I and V for RL = 0 Ω, 100 Ω, 390 Ω, and open circuit
- Calculate VTh and RTh on paper and compare with the measured values (may be done later)
- Thévenin equivalent of the servo's Input Position pot
- With the servo switch off, set the supply to ±6 V and connect red to +, green (or black) to COM, and blue to −; turn the servo on and confirm it works, and note this in the notebook
- Unplug the motor wires from the circuit board so the motor will not run
- Connect the voltmeter's black lead to the servo ground (green banana connector) and its red lead to the Input Position pot's center terminal (yellow wire)
- Turn the pot through its range and record the voltage range; leave it fully clockwise and record the open-circuit voltage (VTh)
- Move the Connect BNC jumper to the Connect Resistor position, which puts a 10 kΩ load from the pot's wiper to ground; record the loaded voltage VL
- Reconnect the motor, turn the supply output on, and confirm the servo works before returning it
- Superposition
- Use the E3631A's two supplies: set supply #1 (the ±25V + output) to 12 V and supply #2 (the +6V output) to 6 V
- Build: supply #1 + through 390 Ω to an output node; 1 kΩ from the output node to ground; 220 Ω from the output node to + of supply #2; both supply − leads to ground; voltmeter from the output node to ground
- With both supplies connected, record Vo (about 7.2 V)
- Zero supply #2 (move its + wire into its − plug) and record Vo(1) (about 3.8 V)
- Restore supply #2, zero supply #1 the same way, and record Vo(2) (about 3.4 V)
- Check-off and conclusion
- Get checked off by the lab instructor
- Write a conclusion covering each objective, the usefulness of Thévenin and superposition, how well measurements and calculations agree, and problems you overcame
Record
- Circuit drawings for the original divider, the RTh measurement, the Thévenin circuit, and the superposition circuit
- Table of I and V for RL = 0, 100 Ω, 390 Ω, and open, for the original circuit and the Thévenin circuit
- One I vs V plot (I vertical, V horizontal) with both sets of points; comment on whether the circuits are equivalent
- Measured VTh and RTh, the calculated values, and their comparison
- Servo pot: voltage range over its travel, open-circuit voltage fully clockwise, loaded voltage with the 10 kΩ load
- Thévenin circuit of the servo pot with VTh, VL, and RL = 10 kΩ shown, and the calculated RTh (its output resistance)
- Superposition: Vo, Vo(1), Vo(2), and a comparison of Vo(1) + Vo(2) with Vo
- Conclusion