Week 7

Steady-state sinusoidal AC: phasors & impedance

Week 5 showed that capacitors and inductors shift sinusoids by 90°; this week turns that into a method. A steady-state sinusoid becomes a phasor (a complex number holding amplitude and phase), differentiation becomes multiplication by jω, and capacitors and inductors become impedances 1/(jωC) and jωL. With complex arithmetic, every DC technique (series and parallel, dividers, KVL and KCL) carries over to AC circuits. The lab measures the 90° current-voltage shifts on the scope and builds simple RC and RL filters, which lead into week 8's frequency response.

Objectives

  • Convert complex numbers between rectangular and polar form (watching the quadrant of the angle) and add, subtract, multiply and divide them by hand or calculator.
  • Convert a sinusoid A cos(ωt + θ) to its phasor A∠θ and back, and find period, frequency, radian frequency and phase lead or lag from a waveform.
  • Add or subtract same-frequency sinusoids with phasors and draw the phasor diagram showing all of them.
  • Write the impedances ZR = R, ZL = jωL and ZC = 1/(jωC) = −j/(ωC), find reactance, and find the C or L that gives a stated impedance magnitude at a stated frequency.
  • Find the equivalent impedance of a series-parallel RLC network in polar form.
  • Solve steady-state AC circuits with phasors using Ohm's law, voltage and current dividers, KVL and KCL, giving currents and voltages in polar and time-domain form and stating which leads.
  • Find an unknown impedance from its voltage and current phasors and decide which parts (resistor with inductor or capacitor, in series or parallel) build it, with their values.
  • Choose and size a capacitor or inductor so that a circuit's current or output voltage leads or lags its source by a specified angle.
  • Draw voltage and current phasors to scale and use the diagram to show KVL or KCL, explaining why peak values of out-of-phase sinusoids don't add.
  • Measure the phase shift between a component's voltage and current with scope cursors (Δt/T × 360°) and with an XY Lissajous figure, using a 1 Ω sense resistor for current.
  • Build RC and RL high-pass, low-pass and band-pass filters, measure their roll-off (70%) frequencies and compare with fc = 1/(2πRC) and R/(2πL).

Reading

2.25–272.25 shows how quickly differential-equation models of AC circuits get messy, which is the reason for phasors; 2.26 reviews complex numbers (rectangular, polar, Euler); 2.27 analyzes sinusoidal circuits with complex impedances. Focus on 2.26 and 2.27.1 to 2.27.2.

Lectures

1
Phasors, examples 1–2Open original recording
13:15
2
Impedance in series & parallelOpen original recording
22:22
3Phasor examples 3–435:46
4
In-class phasor exampleOpen original recording
56:09
2:07:32

Notes

From the notes pack:

  1. Complex numbers: rectangular and polar forms, conversions, special cases (j = ∠90°, 1/j = −j), equality
  2. Complex arithmetic: addition and subtraction (rectangular), multiplication and division (rectangular and polar), powers, conjugates
  3. Euler's equation and why Re[e^(j(ωt+θ))] = cos(ωt + θ) lets e^(jθ) stand for a sinusoid; calculus with phasors (d/dt becomes jω)
  4. Intro to AC phasors: period, frequency, radian frequency, amplitude, phase lead and lag
  5. Phasor definition for voltages and currents; Example 1: adding 4.5 V∠−30° and 3.2 V∠15° with a phasor diagram
  6. Example 2: subtracting two sinusoidal voltages with phasors
  7. Calculus in phasor form and impedance: ZL = jωL, ZC = 1/(jωC), ZR = R
  8. Series impedances and the AC voltage divider (example: 200 Ω, 0.6 µF, 80 mH at 500 Hz with 12 V)
  9. Parallel impedances and the AC current divider (example: the same parts in parallel at 500 Hz)
  10. Phasor Example 1: VR, VL and VC of a series RLC circuit at 2 kHz, with a caution about the quadrant of atan
  11. Phasor Example 2: Zeq, branch currents and VC of an L-C-RL network at 2.5 kHz, and why IC can exceed the input current
  12. Phasor Example 3: find an unknown series impedance from V and I, and which leads
  13. Phasor Example 4: find Vin and IT in a parallel circuit, then build Z = 80 − 60j Ω from a series R and C
  14. Phasor Example 5: build Z = 80 − 60j Ω from a parallel R and C
  15. Phasor Example 6: find I1, lead or lag, and Z2 from given voltages and currents
  16. Phasor Example 7: choose L or C to make the output lead by 40° or lag by 20°
  17. Phasor Example 8: voltage divider with complex impedances

Homework

Ph1: Complex numbers

  1. 1) Convert to polar form: 1 + j, 2.6 + 8.7j, 3 + 4j, 3 − 4j, −3 + 4j, −3 − 4j
  2. 2) Convert to rectangular form: 10∠60°, 0.4∠12°, 1500∠(π/2 rad), 10∠−45°, 20∠120°, 30∠210°
  3. 3) Add or subtract: (3 + 2j) + (6 + 9j), (9 − 10j) − (9 + 10j), (−2 − 2j) + (−6 + 9j), (3 + 0j) − (0 + 9j), (5 + 6j) + 5∠53°, (−2 + 3j) − 8∠−37°
  4. 4) Multiply: (8 + j)×3, (3 + 2j)×j, 20∠40° × 10∠60°, (−6 + 9j) × 10∠60°, (−2 − j)(−6 − 9j)
  5. 5) Divide: 20∠40° / 10∠60°, (9 − 10j) / 3∠−20°, 36 / 9∠90°, (−2 − 2j)(−6 − 9j) / ((−6 + 9j)(−6 − 9j))

Ph2: Phasors and impedance

  1. 1) For z1 = −4 + 5j and z2 = 2 + 4j, check whether |z1z2| = |z1||z2|, |z1/z2| = |z1|/|z2|, and |z1 + z2| = |z1| + |z2|
  2. 2a) Find the phasor of v(t) = 8.4 cos(100t − 90°) in polar and rectangular form
  3. 2b) Find i(t) for the phasor I = (5 + j12) µA at 600 Hz
  4. 3a) Add v1 = 50 V cos(ωt − 60°) and v2 = 24 V cos(ωt + 15°) with phasors; draw the phasor diagram and give v3(t)
  5. 3b) Add v1 = 0.9 V cos(ωt + 72°) and v2 = 1.2 V cos(ωt − 20°); draw the diagram
  6. 3c) Find v4 = v2 − v1 for the same pair and add it to the diagram
  7. 4) Express the impedance of a 5.2 mH inductor at 60 Hz in polar form
  8. 5a) A capacitor's impedance magnitude is 240 Ω at 1.8 kHz; find C
  9. 5b) Find the inductor with the same impedance magnitude at 1.8 kHz
  10. 5c) Find the reactances of that capacitor and inductor at 3.6 kHz
  11. 5d) Find the total impedance of the two in series at 2.7 kHz
  12. 6a) Find Zeq of 330 Ω in series with 100 mH at 1 kHz
  13. 6b) Find Zeq of 330 Ω in series with 0.22 µF at 2 kHz
  14. 6c) Write Zeq of a series R, L and C at 4 kHz symbolically
  15. 6d) Find Zeq of 160 mH in series with (4 kΩ in parallel with 0.03 µF) at 1.5 kHz
  16. 7) Find the current phasor I in each circuit of problem 6 (10 V∠0° sources for a to c, 8 V∠0° for d)
  17. 8a) vs = 14 V cos(377t + 16°) drives R = 180 Ω in series with an unknown Z, and i = 30 mA cos(377t + 36°); find Z
  18. 8b) Which leads, current or voltage? 8c) By how many degrees?
  19. 9a) A resistor and capacitor in series make Z = 50 Ω∠−66° at 3 kHz; find R and C
  20. 9b) Same impedance from a resistor and capacitor in parallel; find R and C (invert Z first)
  21. 10) A load made of a resistor in series with a reactive part draws I = 3.4 A∠−30° from Vs = (60 + j28) V at 60 Hz; find |Z|, R, and the reactive part's type and value
  22. 11) Vs = 12 V∠0° at 500 Hz drives C = 12 µF in series with R = 40 Ω; draw a to-scale phasor diagram of Vs, I, VR and VC showing KVL

Ph3: AC circuit analysis with phasors

  1. 1a) For R = 120 Ω in series with L = 3 mH, find the frequency where |Z| = 240 Ω
  2. 1b) Find the impedance angle at that frequency
  3. 1c) Find the series capacitor that makes the circuit purely resistive at that frequency
  4. 2) vs = 160 V cos(450t) drives R = 500 Ω in series with an unknown part; the current must lead vs by 36°; choose R, L or C for the box and find its value
  5. 3) A parallel circuit has Vs = 50 V at −30°, branch current I1 = 1.3 A at +30° and I2 = 1 A at −53.1° (from a phasor diagram); find Z1 and Z2
  6. 4a) Vs = 24 V∠45° drives Z1 = 100 Ω∠10° and Z2 = 250 Ω∠45° in parallel; find I1, I2 and IT
  7. 4b) Draw I1, I2 and IT to scale to show KCL
  8. 5a) A current source Iin drives Z1 = (120 − 90j) Ω in series with Z2 = 75 Ω∠30°, and the voltage across Z1 is V1 = 9 V (reference angle 0°); find Iin in polar form
  9. 5b) Find the source voltage VT
  10. 5c) Does the source current lead or lag the source voltage?
  11. 6a) Vin drives Z1 and Z2 = 100 Ω∠−30° in parallel; IT = (54 − 8j) mA and I2 = 45 mA∠20°; find Z1
  12. 6b) Choose the simplest parts to build Z1 from a list (resistor, capacitor, inductor, sources, meters, etc.) and say why
  13. 6c) Does I2 lead or lag Vin? 6d) Does I1 lead or lag I2?
  14. 7) Vs = 100 V∠−90° supplies IT = 423 mA∠105° to an unknown Z in parallel with 1 kΩ and with a branch of 200 Ω in series with −200j Ω; find Z
  15. 8a) A 10 V∠0° source drives two parallel branches, (12 − 20j) Ω and (24 + 24j) Ω; find the total impedance
  16. 8b) Find IT
  17. 9) At 8 kHz, find Zeq in polar form of 8 mH in series with 0.02 µF, that branch in parallel with 500 Ω

Lab: Phases and filters (ECE 2210 Lab 7)

Drive a capacitor, then an inductor, in series with a 1 Ω current-sense resistor and measure on the scope that the current leads the capacitor voltage and lags the inductor voltage by 90°, by cursors and by an XY circle. Then build RC and RL low-pass, high-pass and band-pass filters, plot their frequency response and compare measured roll-off frequencies with calculations.

Before the lab

  • Calculate the roll-off frequency of the RC low-pass from the Capacitors lab (1 kΩ, 0.1 µF): fc = 1/(2πRC) ≈ 1.59 kHz
  • Calculate roll-offs for the high-pass RC (1 kΩ, 0.1 µF, ≈ 1.59 kHz), high-pass RL and low-pass RL (1 kΩ, 3.3 mH: fc = R/(2πL) ≈ 48 kHz)
  • Calculate the band-pass roll-offs (100 Ω, 3.3 mH, 0.01 µF): fL = R/(2πL) ≈ 4.8 kHz and fH = 1/(2πRC) ≈ 159 kHz
  • Find your Capacitors lab frequency response curve; you will read its roll-off point
  • Measure your inductor with the HP LCR meter (the TA can show you) and use the measured value instead of 3.3 mH

Equipment

  • Function generator (Agilent/HP 33120A)
  • Oscilloscope (two channels, with cursors and XY mode)
  • Two scope probes, set to 1x
  • HP LCR meter (to measure the inductor)
  • Breadboard and jumper wires

Parts

11 Ω resistorbrown black gold gold; current-sense resistor
1100 Ω resistorbrown black brown
11 kΩ resistor
10.1 µF capacitormarked 104
10.01 µF capacitormarked 103
13.3 mH inductorany 2 to 4 mH inductor

Procedure

  1. Capacitor current and voltage
    • Generator output to the 0.1 µF capacitor, to the 1 Ω resistor, to ground
    • CH1 probe (1x) at the generator side of the capacitor (Vs, essentially the capacitor voltage); CH2 probe (1x) at the capacitor-resistor junction, so CH2 shows the current (1 mV per mA); probe grounds to ground
    • Set the generator to 8 Vpp (most need 4 Vpp on the display) at about 10 kHz
    • Trigger on the cleaner CH1 signal (Trigger key, Source softkey; set the trigger type to edge if needed)
    • Check whether the current (CH2) leads, that is sits to the left of, the voltage
  2. Measure the phase angle
    • Move both channels' ground markers to the screen's center line
    • Adjust volts/div and time/div for two large traces
    • Press Cursors; select X1 and put it on a zero crossing of one trace with the Entry knob; select X2 and put it on the matching zero crossing of the other trace
    • Read ΔX and compute the phase shift as ΔX/T × 360°, with T measured or from 1/f
  3. XY circle
    • Press Horiz, then the Time Mode softkey until XY is checked; CH2 now drives the beam left-right and CH1 up-down
    • Adjust volts/div (and fine-adjust a channel if needed) until the figure is a circle
    • Return Time Mode to Normal
  4. Other frequencies
    • Set the generator to 1 kHz and check whether the phase angle changes; repeat at 30 kHz
    • Watch how the current amplitude changes with frequency
    • Return to 10 kHz
  5. Repeat with the inductor
    • Replace the capacitor with the 3.3 mH inductor
    • Repeat the lead/lag check, the cursor phase measurement at 10 kHz, and the 1 kHz and 30 kHz checks (no need to re-explain the circle)
  6. RC low-pass from the Capacitors lab
    • On your Capacitors lab curve (generator to 1 kΩ, output across 0.1 µF to ground), find the frequency where vo/vin = 0.70
    • Compare it with the calculated fc
  7. One filter with a full curve
    • Build one of: high-pass RC (vin to 0.1 µF, output across 1 kΩ to ground), high-pass RL (vin to 1 kΩ, output across 3.3 mH to ground), or low-pass RL (vin to 3.3 mH, output across 1 kΩ to ground)
    • Drive it from the generator; CH1 on vin, CH2 on vout
    • Measure the output across frequency (1, 3, 10 pattern, a log-2 pattern, log paper, or a computer plot) and plot on a log frequency axis
    • Find the roll-off point on the plot
  8. The other two filters
    • Build each remaining filter, confirm it is high-pass or low-pass as labeled, and find its roll-off frequency (no curve needed)
  9. Band-pass filter
    • vin to 100 Ω, to the output node; from the output node to ground, the 3.3 mH inductor and the 0.01 µF capacitor in parallel
    • Measure the frequency response with many points (the peak should be near 1/(2π√(LC)) ≈ 28 kHz) and plot it on a log axis
    • Find both roll-off points

Record

  • Whether the capacitor current leads the voltage, with ΔX, period, and the computed phase angle; answer: is it 90° as expected?
  • Sketch of the XY circle and an explanation of why it is (almost) a circle
  • Phase and current amplitude at 1 kHz and 30 kHz; answer: does the amplitude change as expected given |ZC| is inversely proportional to frequency?
  • The same measurements for the inductor, showing the current lagging by 90°
  • Answers: what type of filter did you build in the Capacitors lab, and what type is the Resonance lab circuit?
  • Roll-off of the Capacitors lab RC low-pass from its curve compared with the calculation
  • Calculated roll-offs for the three filters
  • Frequency response plot of one filter, with its measured roll-off compared to the calculation
  • Confirmed type and measured roll-off of the other two filters compared to calculations
  • Band-pass frequency response plot with both roll-off frequencies compared to fL and fH
  • Conclusion; get the check-off