Week 8
Frequency response & Bode plots
The filters from the Capacitors, Resonance and Phases labs pass some frequencies and reject others; this week makes that quantitative. You write a circuit's transfer function H(ω) = Vout/Vin with the impedances from week 7, express gain in decibels, and sketch its magnitude quickly with Bode's straight-line method: find the corner frequencies (poles and zeros), approximate H in each frequency range, and join flat and ±20 dB/decade segments. Only magnitude plots are covered; phase plots are left for later courses.
Objectives
- Convert voltage or current ratios to dB with 20 log(V2/V1), power ratios with 10 log(P2/P1), and dB back to ratios, and recall the common values (3 dB ≈ 1.414 or 0.708, 6 dB ≈ 2, 20 dB = 10).
- Derive the transfer function H(ω) = Vout/Vin of an RC or RL filter using impedances and put it in the standard form with terms like (1 + jω/ωc).
- Find the corner frequencies of a transfer function, where a term's real and imaginary parts are equal, and classify each as a pole (denominator) or zero (numerator).
- Approximate |H| in each frequency range between corners by keeping only the dominant part of each term, and give the flat level in dB or the slope (+20 or −20 dB/decade, ±6 dB/octave).
- Draw the straight-line Bode magnitude plot on semilog axes with labeled dB values, then sketch the actual curve, which is 3 dB off the asymptotes at an isolated corner and about 1 dB off one octave away.
- Identify a circuit or transfer function as low-pass, high-pass, band-pass or band-reject (notch) from its components or its Bode plot.
- Explain absolute dB-based units: dBm referenced to 1 mW, VU as dBm into 600 Ω, and sound pressure level referenced to 2 × 10⁻⁵ Pa.
Reading
| 2.29–33 | AC Thévenin equivalents (2.29), resonant circuits with Q and bandwidth (2.30), decibels (2.31), input and output impedance (2.32), and two-port networks, filters and attenuators (2.33). Focus on 2.31 and 2.33.1; skim the rest as background. |
Lectures
| 1 | Bode plotsOpen original recording | 1:17:48 |
| 1:17:48 |
Notes
From the notes pack:
- Frequency response: the output-to-input relationship versus frequency, as measured in the Capacitors and Resonance labs
- Filter circuits: high-pass, low-pass, band-pass, band-reject and notch
- RL high-pass example: transfer function H(ω) = jωL/(R + jωL) and its low- and high-frequency approximations
- Decibels: the bel as a 10× power ratio, 10 log for power, 20 log for voltage and current
- Table of common ratios in dB (±3, ±6, ±20, ±40 dB)
- Other dB-based units: sound pressure level, dBm, volume units (VU)
- Bode plot method: find H, find corner frequencies, approximate each range, draw straight lines, then the actual curve
- Example 1: RC low-pass (100 kΩ, 0.04 µF), one pole at 250 rad/s, −20 dB/decade, −3 dB at the corner
- Example 2: ×50 amplifier driving an RC high-pass (0.2 µF, 10 kΩ), pole at 500 rad/s, +20 dB/decade up to a 34 dB pass band
- Example 3: H(f) = 10(1 + jf/10 Hz)/(1 + jf/500 Hz), a zero and a pole, from 20 dB up to 54 dB
- Example 4: typical amplifier transfer function with poles at 416.67 and 68,750 rad/s and a 37.6 dB pass band
- Warning: these are only magnitude plots of simple cases; real Bode plots include phase and interacting or complex poles
Homework
Bode: Decibels and Bode magnitude plots
- 1) Convert ratios to dB: 4/1, 1/4, 500, 20000
- 2) Convert to voltage ratios: 20 dB, 46 dB, −46 dB, 80 dB
- 3a) For Vin driving R = 30 Ω in series with L = 2 mH, output VL across the inductor, find H(ω)
- 3b) Find the corner frequency
- 3c) Approximate H in each frequency range, with magnitudes in dB and slopes in dB/decade
- 3d) Draw the straight-line Bode plot on the given semilog grid with dB labels
- 3e) Sketch the actual magnitude on the same plot
- 3f) Calculate the actual magnitude at the corner frequency
- 3g) Calculate the actual magnitude one octave above the corner (2ωc)
- 4a) Draw the straight-line Bode plot of Ha(ω) = 20/(1 + jω/(4000 rad/s)), showing the steps
- 4b) Draw the Bode plot of Hb(ω) = 120jω/(400 rad/s + j4ω)
- 4c) Draw the Bode plot of Hc(f) = 0.1(1 + jf/200 Hz)/(1 + jf/20000 Hz)
- 5) Classify the filters of problems 3, 4a, 4b and 4c as low-pass, band-pass or high-pass
- 6a) Draw the straight-line Bode plot of H(f) = (3 kHz + jf)(1 Hz + jf/20)/(jf(jf/400 + 100 Hz)) on the given grid (−10 to 40 dB, 1 Hz to 1 MHz)
- 6b) Sketch the actual magnitude as a dotted line, mark where it differs most from the asymptotes, and give the actual magnitudes there
- 6c) Identify all zeros and poles
Extras
- Semilog graph paper: One page with four blank semilog grids, each spanning six decades (1 to 10⁶) on the horizontal log axis with six linear vertical divisions. Print it for drawing Bode plots and lab frequency response curves.