Labs
Each lab is written out on its week's page. This page has what they share: the parts you buy once, what you borrow from the stockroom, and what the lab notebook should hold.
The labs
Parts kit
| Qty | Part | Used in labs |
|---|
| 1 | Breadboard with wires | 1, 2, 3, 4, 5, 6, 7, 8, 10, 11 |
| 1 | 1 Ω resistor | 7 |
| 1 | 56 Ω resistor | 10 |
| 1 | 100 Ω resistor | 1, 3, 6, 7, 8, 10 |
| 1 | 220 Ω resistor | 3 |
| 1 | 270 Ω resistor | 1, 3 |
| 2 | 390 Ω resistor | 2, 3, 6 |
| 1 | 510 Ω resistor | 10 |
| 1 | 560 Ω resistor | 1, 2, 3 |
| 2 | 1 kΩ resistor | 1, 2, 3, 5, 7, 8, 10 |
| 2 | 2 kΩ resistor | 1, 6 |
| 1 | 2.2 kΩ resistor | 1 |
| 3 | 10 kΩ resistor | 3, 4, 11 |
| 1 | 22 kΩ resistor | 8, 10 |
| 1 | 100 kΩ resistor | 5, 10 |
| 1 | 1 MΩ resistor | |
| 1 | 500 Ω trim potentiometer | 3 |
| 1 | Small screwdriver for the trim pot | 3 |
| 1 | 0.001 µF capacitor (102) | 6, 8 |
| 1 | 0.01 µF capacitor (103) | 7 |
| 2 | 0.1 µF capacitor (104) | 5, 7, 11 |
| 2 | 0.22 µF capacitor (224) | 8, 10, 11 |
| 2 | 47 µF electrolytic capacitor | 5, 10, 11 |
| 1 | 3.3 mH (332) or 2.8 mH (LH233) inductor | 6, 7, 8 |
| 1 | Photoresistor | |
| 1 | LM324 quad op amp | 11 |
| 2 | Condenser microphone | 4 |
| 1 | 1N4002 or 1N4004 diode | 10 |
| 1 | Red LED | 10 |
| 1 | Green LED | 10 |
| 1 | Yellow LED | 10 |
| 1 | 1N4734 5.6 V zener diode | 10 |
| 1 | 2N3904 NPN transistor | 10 |
Borrowed from the stockroom
| Item | Used in labs |
|---|
| Servo | 1, 2, 3, 4, 6, 9, 10, 11 |
| Digital multimeter (portable) | 1, 2, 3 |
| Analog multimeter (BK Precision or similar) | 5 |
| Resistor substitution box | 8 |
| Oscilloscope training kit (HP 54654A) | 4 |
Lab notebook
- Use a notebook you cannot insert pages into (spiral or bound)
- Title and date every lab; date every piece of paper you write on
- Read the whole lab beforehand and write your own objective or introduction; copying the handout's objective may cost credit
- Describe what you did well enough to repeat the lab without the handout; do not cut and paste from it
- Draw a circuit diagram, with part values, of everything you build
- Note the instrument model (for example "Agilent E3631A" by the supply) in at least the first diagram that uses it
- Describe how you used the lab equipment, especially new procedures
- Describe problems you ran into and how you solved them
- Answer every question in the handout, and every request to comment, in complete sentences
- Record all raw data directly in the notebook, with any calculations used to process it
- Put data in tables and graphs whenever possible, for example calculated against measured values; data must never be hard to find
- Draw graphs to scale with a ruler: independent variable on the horizontal axis, points marked as dots or crosses, a smooth averaged line, a title and labeled axes (computer plots taped in are fine)
- End with a conclusion: what you learned, how you met each objective, how close results came to expectations or to other methods, and why they differ